Security Settings
Information in this section of the HP Jetdirect configuration page is described in the following table.
Security Settings
|
|
|
|
|
| Indicates which EAP/802.1X client authentication setting was selected.
|
| Specified An 802.1X authentication protocol other than EAP-TLS/EAP-PEAP was selected.
|
| Not Specified No 802.1X authentication was selected.
|
|
|
|
| If the print server and printer/MFP device supports IPsec, then IPsec appears. If IPsec is not supported, then Firewall appears.
|
| Current IPsec/Firewall status.
|
| Enabled IPsec/Firewall is enabled and operating as configured.
|
| Disabled IPsec/Firewall is turned off.
|
| Policy Failed Print server failed to implement the selected IPsec policy. You might need to reset security (control panel or embedded Web server), or perform a cold reset.
|
|
|
|
| IP Administrator password is set on the print server. This password is shared by Telnet, the embedded Web server, and HP Web Jetadmin to control access to print server configuration parameters. (Consists of up to 16 alphanumeric characters.)
|
| Not Specified Password not set.
|
| Clear the password, using a cold reset.
|
|
|
|
| Expiration date of the digital certificate for SSL/TLS encrypted security. The date is in UTC format (for example, “2012-10-02 12:45 UTC”).
|
| Not Applicable Digital certificate is not installed.
|
|
|
|
| SNMP versions enabled on the print server.
|
| Disabled All SNMP versions disabled. No SNMP access is allowed.
|
| 1;2 SNMP v.1 and SNMP v.2c supported. SNMP v.3 is disabled, or not supported.
|
| 1;2;3-na/np SNMP v.1, v.2c, and v.3 enabled. v.3 is enabled with the minimum security of no authentication (na) and no privacy (np).
|
| 1;2;3-a/np SNMP v.1, v.2c, and v.3 enabled. v.3 is enabled with the minimum security of authentication enabled (a) but no privacy (np).
|
| 1;2;3-a/p SNMP v.1, v.2c, and v.3 enabled. v.3 is enabled with the minimum security of authentication (a) with privacy (p) enabled.
|
| 3-na/np SNMP v.1 and v.2c disabled. SNMP v.3 is enabled with the minimum security of no authentication (na) and no privacy (np).
|
| 3-a/np SNMP v.1 and v.2c disabled. SNMP v.3 is enabled with the minimum security of authentication enabled (a) but no privacy (np).
|
| 3-a/p SNMP v.1 and v.2c disabled. SNMP v.3 is enabled with the minimum security of authentication (a) with privacy (p) enabled.
|
|
|
|
| SNMP set community name is configured on the HP Jetdirect print server. An SNMP set community name is a password for write access to SNMP control functions (SNMP SetRequests) on the HP Jetdirect print server.
|
| Not Specified SNMP set community name is not set.
|
| Specified User-specified SNMP set community is set.
|
|
|
|
| SNMP get community name is configured on the HP Jetdirect print server. This is a password to determine which SNMP GetRequests the HP Jetdirect print server responds to. If a Get community name is set, the print server responds to either a user specified community name or the factory-default.
|
|
|
|
| (IPv4 only) Access control list is set on the HP Jetdirect print server. The list specifies the IP address of individual systems, or IP network of systems, that are allowed access to the print server and device.
|
| Specified Host access list is set.
|
| Not Specified Host access list is not set. All systems are allowed access.
|
|
|
|
| Use encrypted communications between a browser and the HP Jetdirect embedded Web server.
|
| Optional (HTTPS/HTTP) Allows un-encrypted communication using standard HTTP ports, as well as encrypted communications using HTTPS.
|
| HTTPS Required Allow only encrypted communications on HTTPS.
|
|
HP Jetdirect Print Servers Security Settings